I had a 256G SSD boot drive that died. So while I was waiting for warranty replacement, I ran on a 1T magnetic disk. I am now trying to copy back to the replacement 256G SSD and I get the following error while running the Copy Drive Wizard:
Error EC8F17B3: Cannot complete copying of disk0-vista (C:\) drive.
--Cannot copy source drive to destination location.
---Attempt to handle too many NTFS attributes.
---Cannot copy source drive to destination location.
----Attempt to handle too many NTFS attributes.
I have the latest version of ghost. The source drive is clean with no errors. Any ideas?
I have the "resize" box checked, and I delete the partion from the destination drive before each attempt (so it shows as "unallocated space"). My source drive only has about 150G so should fit with no issues on the 256G disk.
My Ghost version is 14 and when I run LiveUpdate, it says I'm up to date. The "too many attributes" error hits I found when I googled implied a chkdsk issue on the source drive but chkdsk runs clean both in a command prompt and when run during reboot.
I'm not familiar with 1T magnetic disks. Did you do Copy Drive from your SSD to the magnetic disk. Was that before the SSD became "sick"? What size was the Vista partition on the 256 GB SSD?
If you can't correct the error I suggest imaging (recovery point) the current Vista partition and restoring the image to the new SSD. I'm not sure what will happen to your starting sector offset.
When the original SSD died, I restored onto a temporary 1T disk (using Ghost). Now I'm ready to move back to the replacement SSD. My error happens exactly the same time as the other thread -- once it's done copying data, so at 99% and the last few seconds.
So, I'll probably wait till next weekend to try again and if I don't hear any good work-arounds, I'll try to just do a restore onto the replacement SSD.
Just to sort out confusing terminology. You restored an image to the magnetic disk. You didn't do Copy Drive to the magnetic disk. Correct?
Do you still have the original image?
I read the other thread and I wasn't convinced the error was due to not copying into unallocated space. I know you have been copying into unallocated space.
This system is a desktop -- home grown Core i7 system.
I didn't do a "drive copy" when I set up the temporary magnetic disk because the original SSD died unexpectedly so I had to restore from backup to get my current temporary drive up and running. I've lived on the temporary drive for the last month or so, continuing to do regular full/incremental backups. When the replacement SSD finally showed up, I figured I'd have fewer hastles by just doing "copy drive" to get it set up rather than doing a restore since my full backup only runs once a week (incremental runs daily).
This is part of a multi-drive setup. The SSD is my boot/system drive and I have another magnetic disk as my user drive that is mounted under \Users (OS is Vista).
Message Edited by johndkeene on 10-03-2009 04:14 PM
And I shouldn't have any issues with my mount point that links in my user drive? That should all restore OK even though I'm not restoring my user drive (only the boot drive)?
I don’t use mount points so I’m not sure. When I restore my C: drive, all links to other partitions work. For example, my page file is in E: drive, My Documents are in D: drive, Outlook Express store is in D: drive etc. Does that help?
OK, finally had time to just try and do a restore -- same results (says too many NTFS attributes) in that it dies at 99%. Any way to tell how many NTFS attributes would not be "too many" and any way to "get rid" of the ones I don't want? :D
I'm open to other suggestions to try or to try and get more debug info for this issue.
So I tried a couple other things as well. I shrunk the current drive down so it is smaller than the destination drive. This took a little work because Vista didn't want to shrink. I figured out that it was shadow copy space that was holding on to the free space. So I used vssadmin to shrink that down, then shrunk the drive. It's now about 220G in size (only 150G in use) and the SSD is 256G. Ran both a drive to drive copy and a backup and restore. Same results.... it gets to the last step after copying all data (like 5 seconds left) and says:
Attempt to handle too many NTFS attributes
So my question now is what about NTFS attributes makes it "too many"? Given all this trouble, I'm feel a bit exposed in that there might be some reason that would prevent me from restoring to any drive, much less my desired SSD drive.
I had a 256G SSD boot drive that died. So while I was waiting for warranty replacement, I ran on a 1T magnetic disk. I am now trying to copy back to the replacement 256G SSD and I get the following error while running the Copy Drive Wizard:
Error EC8F17B3: Cannot complete copying of disk0-vista (C:\) drive.
--Cannot copy source drive to destination location.
---Attempt to handle too many NTFS attributes.
---Cannot copy source drive to destination location.
----Attempt to handle too many NTFS attributes.
I have the latest version of ghost. The source drive is clean with no errors. Any ideas?